Brickcom OB-v2-series Instrukcja Użytkownika Strona 1

Hardware User’s Manual Megapixel Day & Night Outdoor Bullet Network Camera Quality Service Group Outdoor Bullet V2 Series

7 m. Power adapter B. Wi-Fi Antenna Package contents (Optional) Refer to the installation guide included in the package when installing the Wi-

8 C. Wi-Fi Antenna Package contents (Optional) Refer to the installation guide included in the package when installing the 3G antenna a. 3G Ante

9 Chapter 2 - Outdoor Bullet Network Camera Overview The Brickcom Outdoor Bullet SERIES is an outdoor bullet network camera. It adopts a megapix

10 Chapter 3 - Device Appearance Description < Front Panel > < Rear Panel > < Top >

11 < Bottom > < Side > **3G SIM Card Slot only apply for GOB-100Ap/GOB-130Np/GOB-132Np/GOB-500Ap GOB-502Ap/GOB-302Np/GOB-300Np**

12 <Inside> TV out Connector ***This function only apply below models.*** OB-502A Series/OB-500A Series and OB-302N Series/OB-300NSeries

13 < DI/DO Diagram >

14 OB-100Ap Series and OB-130N Series Reset button OB-502A Series and OB-302N Series Reset Button and WPS button **WPS Button only applies for

15 < Hardware Reset > The Reset Button can be used to reboot the camera or restore it to factory default settings. If the camera experiences

16 Chapter 4 - Installation 4.1 Hardware Installation WARNING - Do not mount the camera on a soft material. The camera may fall and be damaged. A

Review History: 1. Separate User Manual into HW and SW. 2. Merge OB-100A V2 series /OB-130N-series into this User Manual. 3. Add OB-500A Series /

17 B. Wall Installation Using the Optional Bracket a. Using the Bracket plate as a guide, drill three holes into the wall and hammer the supplied p

18 d. Connect (1) the POE cable; (2) DIDO, Audio In/Out, RS485 cable; and (3) Antenna cable with the camera. Refer to step 3 for more details in

19 C. DIDO, Audio In/Out, RS485, and Antenna Connection a. PoE Connection For the Power over Ethernet connection, construct the PoE cable using th

20 b. DIDO, Audio In/Out, RS485 Cable Connection For the DIDO, Audio In/Out and RS485 cable connection, construct an Ethernet cable using the pin d

21 c. WiFi or 3G Antenna Extension Cable Connection Pass the Antenna extension cable (1) through and bracket and connect it to the Antenna

22 4.2 Camera Connection The Outdoor Bullet Series is PoE compliant, so there are two options for connecting the camera to a power and Ether

23 c. If using a PoE injector as power input (For GOB/WOB Series): i. Use a standard RJ-45 cable to connect the camera to a PoE Injector. ii. Us

24 4.3 System Requirements Operating System: Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 Computer: IBM PC/AT

25 4.4 Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refe

26 B. In the Install Shield Wizard dialog box, click <Next> to continue. C. Read the End-User License Agreement and check the option “I acc

Table of ContentsBefore You Use This Product ... 1 Regulatory In

27 D. Select either “Complete” setup or “Custom” setup to install the system. a. If COMPLETE SETUP is selected: i. All program features will b

28 iii. Select to create shortcuts. Click <Next> to continue. iv. The installation information will be displayed. Click <Next>

29 v. To launch EasyConfig or PC-NVR Standard, select the application and click <Finish>. When launching the PC-NVR program, please refer to

30 iii. Select the features to install. Click <Next> to continue. iv. Click <Change> to change the appointed folder where installatio

31 v. Select programs to create shortcuts. Click <Next> to continue. vi. The installation information will be displayed. Click <N

32 E. To launch EasyConfig or PC-NVR Standard, select the application and click <Finish>. When launching the PC-NVR program, please re

33 4.4.1 EasyConfig To launch EasyConfig, select EasyConfig from the start menu. If Complete Setup type was used in the software installat

34

35 B. Select either “Simple Mode” or “Professional Mode” to obtain the camera’s IP settings. If “Simple Mode” is selected, EasyConfig will

36 C. There may be many cameras in the local network. Differentiate the cameras using their UPnP name. Double click on the camera from the survey l

1 Before You Use This Product In many countries, there are laws prohibiting or restricting the use of surveillance devices. This Network

37 If <Set IP Address configuration manually> is selected, the following pages will be displayed.

38 E. If the camera supports the EasyLinkTM function, the following page will be displayed. Otherwise, this page will not be shown. *If desired,

39 F. When the IP address settings have been configured, the screen will either display a successful or failed connection message. If the connectio

40 c. If the connection was successful, the user will see the message: “Congratulations. The installation of the camera is complete.”

2 Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits

3 Industry Canada statement: Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence

4 Ce dispositif a ete concu pour fonctionner avec une antenne ayant un gain maximal de dB [2.02]. Une antenne a gain plus eleve est strictement inte

5 Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilis

6 Chapter 1 - Package Contents Please check to make sure the product package contains all the accessories listed below. A. Camera Package Contents